%%EOF Insert instead: (1) A pair of direction indicator lights fitted to a vehicle must be spaced as follows: (a) lights fitted to the front of a motor bike or the single wheel end of a motor trike must be spaced in accordance with the requirements for the position of front indicators set out in paragraph 6.3.3.1 of Appendix A to third edition ADR It may, in addition, be equipped with the following lighting and light-signalling devices; 5.15.1. vehicle-hazard warning signal (paragraph 6.9. For LA category vehicles: The technical requirements of any of the editions of United Nations Economic Commission for Europe Regulation No. Approval granted/refused/extended/withdrawn:2/. 6.3. The approval number indicates that the approval was granted in accordance with the requirements of Regulation No. 2.5.6., 2.5.7. and 2.5.15.) 0000002014 00000 n The horizontal angles beta, correspond to the longitude and the vertical angles alpha to the latitude. Motorcycles : VicRoads The illuminating lamps shall be so installed that correct adjustment of their orientation can easily be carried out. 0000008826 00000 n 7.1. 8. The vertical orientation of the passing beam shall remain between - 0.5 % and - 2.5 % of downward inclination for the conditions of loading vehicle plus driver, 9.7. 51 21 A heavy vehicle is a motor vehicle with a GVM exceeding 4.5 tonnes or a trailer with an ATM exceeding 4.5 tonnes. This compilation of Vehicle Standard (Australian Design Rule 19/01 Installation of Lighting and Light-Signalling Devices on L-Group Vehicles) 2007 includes all the instruments set out in the Table of Instruments. In the absence of specific instructions, the height and orientation of the lamps shall be verified with the vehicle unladen and placed on a flat horizontal surface, its median longitudinal plane being vertical and the handlebars being in the position corresponding to the straight ahead movement. May reduce risk of inexperienced riders having crashes associated with inadequate gap selection or awareness of pedestrians/other road users while filtering. Life Membership Policy. This Standard is the Vehicle Standard (Australian Design Rule 19/01 Installation of Lighting and Light-Signalling Devices on L-Group Vehicles) 2007. Illuminating surface of a lighting device (paragraphs. A motorcycle or motorcycle fitted with a sidecar manufactured on or after 1 October 1991 is required to have direction indicators fitted. Rear reflex reflectors, non-triangular: yes/no 2/. 9.5. stop lamp means the lamp used to indicate to other road-users to the rear of the vehicle that its driver is applying the service brake; 2.5.10. 2.4. Vehicles certified to any of the Acceptable Prior Rules, as shown below in the applicability table for a particular vehicle category, are deemed to comply with this rule. This package of reforms is a result of close consultation with key stakeholders such as the NSW Motorcycle Alliance, Motorcycle Council of NSW and NSW Police. 7.4.2. The length: at the front of the vehicle. Horizontal angle: 45 degrees to left and to right for a single lamp; 45 degrees outwards and 10 degrees inwards for each pair of lamps; Vertical angle: 15 degrees above and below the horizontal. Confirmation or refusal of approval, specifying the alternatives, shall be communicated by the procedure specified in paragraph 4.3. above to the Parties to the Agreement which apply this Regulation. 78 already included the 02 series of amendments. In height: not less than 250 mm and not more than 1,200 mm above the ground. ); 5.14.7. rear position lamp (paragraph 6.7. http://www.infrastructure.gov.au/roads/motor/design/adr_online.aspx, (You must log in or sign up to reply here. 9. 6. This Standard also repeals each instrument made under section 7 of the Motor Vehicle Standards Act 1989 that creates a vehicle standard with the name Australian Design Rule 14/02 Rear Vision Mirrors, if there are no other vehicle standards created by that instrument, or amendments to vehicle standards made by that instrument, that are still in This Standard may also be cited as Australian Design Rule 19/01 Installation of Lighting and Light-Signalling Devices on L-Group Vehicles. The vertical angle below the horizontal may be reduced to 5 degrees , however, if the height of the retro-reflector is less than 750 mm. Shouldn't this be posted in "bling and appearance"? The law states a stationary vehicle's indicator signal must be activated for at least five seconds before re-entering the flow of traffic ie. device means a component or combination of components used in order to perform one or several functions. SCOPE. Nevertheless, when the vertical angle of geometric visibility below the horizontal may be reduced to 5 degrees (lamp at less than 750 mm above the ground) the photometric field of measurements of the installed optical unit may be reduced to 5 degrees below the horizontal; 2.12. 10. 0000005842 00000 n The following individual requirements are additional to the requirements set out in Appendix A. Rear blinkers have to be at least 18 cm apart. 1.2.1. 2/ Driver: a simulated mass of 75 kg +/- 1 kg. Get directions. 5.3. 6 or category 12 specified in Regulation No. SUPPLEMENTARY INDIVIDUAL SPECIFICATIONS. The illuminating surface of the reflex reflector may have parts in common with that of any other front lamp. Anyway, the bike was a one-off in Australia - no more have ever been officially imported. In height: not less than 350 mm nor more than 1200 mm above the ground. (The initial downward inclination of the cut-off of the passing beam shall be checked against the requirements of paragraph 6.2.5.). The lamp(s) may move with the steering angle. NOTES, 10.1. 11, 0. legislative provisions, 0.1. Clearly defines the maximum speed riders are allowed to filter at.