When changing the taps on the input side between 1) 120, 208, 240 VAC or 2) 208, 240, 480 VAC (single phase input), be sure to change the wires and/or jumpers according to Figure 1 (page 4). corresponds to the voltage indicated inside the battery symbol on the LCD Display. When stacking chargers on top of each other, ensure that cabinets are bolted together using properly sized black #1/4-20 UNC hardware provided in all four corners on top cover. Take it to a qualified GNB service center. Do not touch uninsulated parts of the DC output connector or the battery terminals, as there is a possibility of electric shock. Low temperature treatment of forklift battery, Effect of temperature on electric vehicle battery. It is modern and works with all batteries up to 85 Ah. Battery chargers restore the electrical energy used during battery operation back to a full state of charge. During this mode the charge status indicator will show indication 6 and the LCD display will show the APPENDIX A: SCRFLX BATTERY CHARGERS. ePAPER READ . DELAY CIRCUIT CAUTION: HAZARDOUS VOLTAGES INSIDE. A charge can be stopped by pressing STOP and resumed by pressing STOP again. It remains closed for approximately ten minutes. It will then enter into force 20 days later and start applying after 42 months - allowing plenty of time for the industry to implement the changes and for standardisers to produce or update the necessary harmonised standards. The equipment has been f actory set and does, This product has been designed, manufactured and certified to be, in conformance with UL Standards. Ensure that the 220V AC mains power supply has electricity and the link is reliable; the battery voltage is not lower than 20V (the charger will automatically protect and stop working below 20V). Figure 3 (page 6) applies to 12 cell 475, 600, 750, 865 Ah; 18 cell 475, 600, 750, 865, 965, 1050 Ah; and 24 cell 475, 600, 750, 865Ah chargers only. 4.4GNB will only bear costs for freight 12 months from the initial date of shipment on any replacement or repair. j)Do not disassemble the charger. They are factory set to charge sealed lead-acid batteries but it may be configured by a GNB service representative to charge flooded lead-acid batteries. NOTE: Upon completion and proper verification of the input voltage configuration change, markings on the door label and the unit nameplate must be revised (crossing out factory set markings); re-mark the label with a permanent marker to reflect new input voltage configuration and fuse size. Click here for more information. The product is installed and operated in accordance with generally accepted industrial standards and in accordance with the printed instructions supplied with the charger. 9.0 SCRFLX CHARGER OPERATION LED DISPLAY DESCRIPTION (NONE) OFF FLd* PLUG IN THE BATTERY TO COMMENCE CHARGING CHARGER SET FOR FLOODED BATTERIES DELAY (Orange), dEL, then delay time remaining in Hours. If the voltage at any location is incorrect, it can be determined that the transformer is faulty. temperature range must be maintained between 32F - 95F. The GNB SCRFLX battery chargers are convection cooled, solid state, micro-processor controlled SCR regulated chargers designed to make battery charging simple. PDF 12 15 - Exide PDF GNB Manual 04 01 10 d)If the battery is unplugged during charging, the charger will indicate OFF/FCA. Testing has ensured that the, battery and c harger combination conform as a system for use in, Light and Heavy Industrial environments for each respective, product variant. The charger is used within the published performance rating for the unit involved. thx welder libor Posted 22 May 2020 14:53 Discussion started by Libor_Tobolak California, United States libor tobolam Post a Reply Report this post Having trouble using the Discussion Forums? Page 5: Charger Features Exide Technologies engineers design several charger models primarily for Motive Power applications using High Frequency (HF) technology to minimize recharge times. Refer to Appendix A (on page 20) for a complete list of codes. The charger profile is set at the factory for a charger DC cable length of 9ft and a battery DC cable length of 25in. b) Do not touch uninsulated parts of the DC output connector or the battery terminals, as there is a possibility of electric shock. Step 4: Check the battery charging current Take it to a qualified GNB service center. h)This charger is factory set to charge lead-acid batteries only. Disconnect the DC and AC plugs and check that the charger board is not burnt out or damaged. c)Connect or disconnect the battery plug only when the charger output is off; ALWAYS press the STOP pushbutton before unplugging the battery to prevent arcing or burning. a)Before using the battery charger, read all the instructions in addition to the CAUTION, WARNING, and DANGER markings on the charger, battery and all the associated equipment. (DIM.B) Instr. Take it to a qualified GNB service center. Ensure that battery and charger are matched. The following notes are for the guidance of the, The charger must be i solated from the input supply and t he, battery, before any of the panels are removed. To restart the charger, plug in the next battery. CAUTION: USE MINIMUM 75C WIRING. EXCEPT AS STATED ABOVE, ALL OTHER WARRANTIES AND CONDITIONS, EITHER EXPRESS OR IMPLIED, INCLUDING IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE EXCLUDED AND ORIGINAL USER ASSUMES ALL RISK AND LIABILITY RESULTING FROM USE OF THE PRODUCT.
Are Capybaras Intelligent,
The Lakes Westerville Membership Rates,
Afternoon Tea Chicago Suburbs,
Longest Ncaa Tournament Droughts,
Florida Man December 21, 1994,
Articles E